Mobile Device is not supported
Connect device
Demo
GEONWORKS VENOM HE
Remap
Actuation
Advanced
KeyTest
Setting
Debug
English
한글
Connect device
Device : SharpKB (DEMO)
S/N :
Profile 0
Profile 1
Profile 2
Profile 3
Firmware Update
Current Firmware :
Layer 0
Layer 1
Layer 2
Layer 3
Layout
Clone Profile 0
Reset All Global
Reset to Global
Show Keybind
Deselect All
Advance Key
Add Modifier
Tap Hold
L-Ctrl
L-Shift
L-Alt
L-Win
R-Ctrl
R-Shift
R-Alt
R-Win
Tap and Hold will perform different actions.
Tap
Hold
Basic Characters
Advance Characters
Special Characters
Keyboard Layer
Keyboard Setting
Actuation Point : 1.50 mm (Global)
Distance required to trigger first keypress after fully release.
Rapid Trigger Upstroke : 0.50 mm (Global)
When rapid trigger is activated, this is the minimum release distance required to release the keypress.
Rapid Trigger Downstroke : 0.50 mm (Global)
When rapid trigger is activated, this is the minimum press distance required to activate the keypress.
Rapid Trigger
When rapid trigger is activated, the actuation point changes dynamically based on the current distance.
Continuous Rapid Trigger
When continuous rapid trigger is activated, rapid trigger function will stop when the key is fully released.
Deadzone : 4.05 mm - 4.10 mm (Global)
This feature prevents the release of a keypress when shaking keycaps while bottoming out a key. Only apply with key that enable rapid trigger.
Test Keybind
Raw matrix test
Enable raw matrix to check each key is working normally. it will automatic disable when leaving from this tab. (This function will request a lot of data that will cause lower scanrate. please do not turn on this function while gaming)
Reset Keypress
Firmware Update
Firmware Update
Current Switch :
Change Switch
Geonworks Raw HE (3.4 mm)
Geonworks Raptor HE (4.0 mm)
Gateron Magnetic Jade (3.5 mm)
Gateron Magnetic (4.1 mm)
NKRO
When disable, keyboard will send in 6 Keys Rollover Mode.
Reset Keyboard to Default Config
Factory Reset
Recalibrate
This function will recalibrate distance of magnetic switch. When you start recalibrate, It will reset a distance that autosave in auto calibration.
Recalibrate
Auto Calibration
When enable auto calibration, it will remember bottom out distance.
This page will request a lot of data that will cause lower scanrate. please do not stay in this page while gaming.
Key 1
Key 2
Select 2 keys to enable SOCD function.
(Warning! This function is not allowed in some games. Use it at your own risk)
Test Keybind
SOCD (Simultaneous Opposing Cardinal Directions)
Only register latest activated key.
Advanced SOCD
Register input only the key that is pressed the deepest. If the difference in distance is less than 0.1 mm, both keys will be register.
Neutral
If both keys are activated, both key are not register.
{} key priority
If this key is activated, it will always register and cannot be interrupted by any other key.
{} key priority
If this key is activated, it will always register and cannot be interrupted by any other key.
Register both keys when both are fully pressed
When both keys are fully pressed, it will register both inputs like a normal keyboard
Reset all setting?
All key will be reset to global value.
Cancel
Reset
Factory Reset?
All setting will be reset to default.
Cancel
Reset
Layout Setting
7U
Split Backspace
Cancel
Apply
testing2
Current Firmware :
New Firmware :
Select Version
Stable Version
Beta Version
Reboot Device to Bootloader Mode
Enter Bootloader
Reconnect Device in Bootloader Mode (IAP)
Connect Device
When device is connect click this button to start update firmware
Start Update
Status :
Exit Bootloader
Close